If your bathtub is old and outdated, you may be considering a remodel. But instead of simply replacing your tub, you may want to consider changing it into a shower. This can be a more cost-effective option and can give your bathroom a more updated look.
- Decide if you want to replace your bathtub or convert it to a shower
- If you want to replace your bathtub, skip to step 4
- Remove the tub faucet and any other fixtures on the tub
- Use a drill to remove the screws holding these fixtures in place
- Cover the drain hole with a plug or rubber stopper so that water doesn’t escape when you remove the tub
- Measure the dimensions of your bathroom and purchase a new shower insert that will fit in the space where your old tub was located
- Many online retailers offer a wide selection of shower inserts, including corner showers, walk-in showers, and alcove showers
- Be sure to measure both the width and height of your space before making your purchase so that you select an insert that will fit properly
- Some stores may also sell pre-fabricated shower stalls that are easy to install
- These can be a great option if you’re not comfortable replacing your own bathtub or don’t have the tools necessary for a more complex installation
- If you go this route, simply follow the instructions included with your purchase
- Most prefabricated showers come with everything needed for installation, including walls, base pan, door, and hardware
- However, you will need to provide your own plumbing fixtures (shower head, valves, etc
- ), which can be purchased at most home improvement stores
- )If you chose to convert your bathtub into a shower instead of replacing it outright,
- Begin by removing any tile or other material that is surrounding your tub on all sides… Next,
- use a sawzall or reciprocating saw to cut through the caulk sealant around the edge of your tub… Once all of the old material has been removed,
- You should have an open space where your new shower can be installed… Now,
- It’s time to install backer board around the perimeter of this opening…
- After cutting pieces of backer board to fit snugly against each wall,, use construction adhesive glue them into place…
- Nail each piece of backer board into place using 1 ¼ inch galvanized nails,, being sure drive them every 6 inches along each stud…
- Finally,, apply joint compound over all seams between pieces off backer board,, as well as any screw holes,, then allow this compound time dry completely… Your new shower area is now ready for waterproofing and t
DIY How to Renovate the Tub / Shower from A to Z
Convert Bathtub to Walk-In Shower
One of the most common home improvement projects is converting a bathtub to a walk-in shower. It’s a project that can be completed in a weekend and will make your bathroom more functional and stylish. Here’s everything you need to know about converting a bathtub to a walk-in shower:
1. Decide if you want to keep your existing tub or remove it entirely. If you plan on removing the tub, you’ll need to factor in the cost of disposing of it properly.
2. Choose the type of shower enclosure you want.
There are many different styles available, so take some time to browse through your options and pick one that fits your taste and budget.
3. Install the new shower base. This is usually a very straightforward process, but be sure to follow the instructions carefully so that everything is installed correctly and securely.
4. Hang the shower curtain or doors. Again, there are many different styles available, so take your time in choosing something that compliments the rest of your bathroom décor.
5. Add any final touches, such as towel racks or soap dishes, and then enjoy your new walk-in shower!
Convert Bathtub to Walk-In Shower Cost
Converting your bathtub to a walk-in shower can be a great way to update your bathroom and make it more accessible. The cost of this project will vary depending on the size and style of your bathroom, but you can expect to spend around $2,000 – $3,000. Here’s a breakdown of what you can expect:
– Demolition: This is the most labor-intensive part of the project and will likely account for about half of the total cost. Your contractor will need to remove the existing tub, as well as any tile or other materials that are in the way.
– Plumbing: You’ll need to have a new shower pan installed, as well as new drains and water lines.
This should add another $500 – $1,000 to the total cost.
– Walls: If you’re converting an alcove bathtub, you may not need to do anything to the walls. But if you’re removing a free-standing tub, you’ll need to patch and repair any damage that was done during demolition.
You may also want to install new waterproofing materials behind the wallboard. This could add another $500 – $1,000 onto your total bill.
Convert Tub to Shower Kit
If you are looking to convert your bathtub into a shower, there are a few things you need to know. First, there are many different types of tub-to-shower conversion kits available on the market. Some kits are designed for specific types of tubs, while others can be used with any type of tub.
Second, when converting your tub to a shower, it is important to make sure that the new shower stall will fit in the space where the old tub was located. Third, you will need to install a new shower drain in order to complete the project. Finally, once the kit is installed, you will need to caulk and seal around the new shower stall in order to prevent leaks.
Best Tub to Shower Conversion
Are you considering a tub to shower conversion for your bathroom? If so, you’re not alone – this is a popular project among homeowners who want to update their space. But with so many options on the market, it can be tough to know which one is right for you.
In this blog post, we’ll break down everything you need to know about tub to shower conversions, including the different types of products available and what factors to consider when making your decision. By the end, you’ll be ready to choose the best option for your home.
Let’s get started!
Credit: www.bathplanet.com
How Much Does It Cost to Convert a Bath Tub into a Shower?
The cost of converting a bathtub into a shower will vary depending on the materials used and the size of the tub. The average cost for a basic conversion using standard materials is between $300 and $500. For a more elaborate conversion using high-end materials, the cost can be upwards of $1,000.
How Do You Convert a Bathtub to a Shower?
If you’re interested in converting your bathtub to a shower, there are a few things you’ll need to do. First, you’ll need to remove the tub and all of the surrounding materials. This includes the tile, drywall, and any other materials that may be in the way.
Once everything is removed, you’ll need to install a shower base and surround. You can do this yourself or hire a professional. If you’re doing it yourself, make sure you follow all directions carefully and take your time.
After the base and surround are installed, you can then add new tile, drywall, and any other finishing touches you desire.
Is It Worth Converting Bathtub to Shower?
If you’re thinking about converting your bathtub to a shower, there are a few things to consider. First, think about how often you use your tub. If you seldom take baths, or if you have another tub in the house that you can use for bathing, then converting your primary tub to a shower might make sense.
Second, consider whether you have the space for a separate shower stall. In many houses, the bathroom is too small to accommodate both a tub and a separate shower. Third, think about your budget.
Converting a bathtub to a shower requires some plumbing and tile work, which can be costly. Finally, keep in mind that taking away your bathtub will decrease the resale value of your home. So if you’re planning on selling in the near future, it’s probably best to keep the tub.
How Do You Convert a Tub to a Tiled Shower?
Converting a tub to a tiled shower is not as difficult as one might think. The first step is to remove the tub and any surrounding trim. Next, install backer board on the walls where the tile will be going.
Once the backer board is in place, you can begin installing your tile. Start at the bottom and work your way up, making sure to use spacers between each tile. When you get to the top, you may need to cut some tiles to fit.
After the tile is installed, grout it in place and then add any finishing touches like caulk or trim.
Conclusion
If you’re looking to update your bathroom, one of the most popular trends is swapping out a bathtub for a walk-in shower. Not only can this create a more open and spacious feel in your small bathroom, but it’s also a more practical solution if you don’t really enjoy baths. Plus, it can be a relatively easy and affordable remodel.
To start, you’ll need to remove your existing tub, which means removing the drain pipes and caulking around the edges. Once that’s done, you can install backer board around the perimeter of the shower area and add tile or another waterproof material to create your new shower space. Finish things off by adding a new shower head, faucet, and any other desired features like shelves or benches.
